| 215 | 2 | 56 |
| 下载次数 | 被引频次 | 阅读次数 |
本文在分析传统煤粉炉水煤比控制的基础上,针对超临界循环流化床锅炉具有很大的燃烧惯性和床料热惯性的特性,提出了利用风量、氧量构造热量信号,并将构造的热量信号引入给水系统中,作为给水流量指令的前馈信号,再用中间点温度或焓值修正作为给水流量指令。热量信号的引入克服了循环流化床锅炉由于床料热惯性、燃烧惯性、给煤量内部扰动和煤质变化对给水控制的不利影响。设计的水煤比控制系统不仅适用于循环流化床锅炉,同时也适用于煤粉炉。
Abstract：Heat release signal constructed by air flow and oxygen content was proposed to improve water-coal rate control in supercritical circulating fluidized boiler where fuel inertia and bed material heat inertia was severe.Different from the traditional method,heat release signal was used as feedforward signal of feed water setpoint.Then the feedwater setpoint was revised by intermediate point temperature or enthalpy.The introduction of heat release signal lowers the passive influence of bed material heat inertia,fuel inertia,feed fuel disturbance and coal quality changes on feed water control.The water-coal rate control can be applied to circulating fluidized boiler as well as pulverized coal boiler.
[1]刘吉臻.协调控制与给水全程控制[M].北京:中国电力出版社,1995:15-43.
[2]李金晶,李艳,吕俊复等.循环流化床锅炉热惯性分析[J].热能动力工程,2009,24(5):609-613.
[3]林文孚.600MW超临界机组给水控制系统及其仿真研究[J].武汉电力职业技术学报,2006,4(3):51-54.
[4]徐二树,李恕康,孙志英等.大容量超临界直流锅炉锅内过程全工况实时仿真数学模型及动态特性[J].动力工程,2003,23(4):2500-2505.
[5]韩忠旭,潘钢,邱忠昌等.直流炉机组给水控制系统的设计与应用[J].中国电机工程学报,2010,30(2):7-15.
[6]何同祥,牛玉广,王存旭等.采用控制中间点焓值的直流炉给水控制系统[J].华东电力,1999,(2):26-28.
[7]何毅,罗自学,刘智等.直流锅炉燃料/给水比值控制的研究[J].湖北电力,2007,31(1):44-46.
[8]田亮,刘鑫屏,赵征等.一种新的热量信号构造方法及实验研究[J].动力工程,2006,26(4):499-502.
[9]马素霞,杨献勇.循环流化床锅炉燃烧系统的动态特性研究[J].中国电机工程学报,2006,26(9):1-6.
[10]郝勇生,沈炯,侯子良等.300MW循环流化床锅炉负荷、床温和床压的动态特性分析[J].动力工程学报,2010,30(3):175-179.
基本信息:
中图分类号:TK227.1
引用信息:
[1]田亮,苏保光,刘吉臻.超临界循环流化床锅炉水煤比控制[J].山东电力高等专科学校学报,2012,15(04):42-45.
2012-08-15
2012-08-15